Circuit Breaker & AutomaticTransfer Switch - Products - WENZHOU CHENLU IMP&EXP CO.LTD

Search

Product List

Products List

ANM6(ABS,ABE)-(1)

ANM6(ABS,ABE)-(1)

MCCB(molded cas...

VDP-VSC5

Mainly used in ...

ANM5(DPX3)

MCCB(molded cas...

Circuit Breaker & AutomaticTransfer Switch

You are here: Home > Products

MCCB(molded case circuit breaker) is a device to protect the equipment from short-circuit, overload. Our MCCB are made according IEC60947-2 standards, rated current from 63A to 1600A are available. Based on the tripping method, we cover thermal-magnetic type and electronic type. According to your application, auxiliary contact, shunt trip, alarming contact, under voltage modular, rotary handle, insert base and residual protection modular etc. are ready well for your special requirement. Mini circuit breaker is the new product adopt the newest modern highly technologic.Its excellent performance is depending on the quick trip and strong .It has some new design for choose.

ANM11(NF-CS)

Rated voltage Rated operating voltage (Un), rated insulation voltage (Ui) and rated pulse voltage. The rated operating voltage of the circuit breaker is the voltage value associated with the breaking capacity and the use category. For AC multiphase circuit finger circuit voltage. The rated operating voltage is numerically dependent on the rated voltage level of the grid. I standard standards for the exchange of 220,380,660 and 1140V, DC 220,440 V and so on. It should be noted that the same circuit breaker can be specified for use at several rated operating voltages, but the corresponding on-off capability is not the same. The rated insulation voltage is the voltage value of the circuit breaker. The electrical clearance and creepage distance of the switchgear shall be determined according to this voltage value. Under normal circumstances, the rated insulation voltage is the maximum rated operating voltage of the circuit breaker. Switch electrical work, to withstand the system occurred in the over-voltage. Therefore, the rated voltage withstand voltage is given in the rated voltage parameter of the switchgear (including the circuit breaker), which should be greater than or equal to the maximum overvoltage peak occurring in the system. Rated insulation voltage and rated pulse voltage together determine the insulation level of the switchgear.

ANTM2

C45-TMseries circuit breaker is used in lighting distribution system or motor distribution system for protecting overload and short-circuit in the system. The product is novel in structure, light in weight, reliable and excellent in performance. It has high breaking capacity, can trip quickly and Its installation uses with guide, Its case and items are adopted with high fire-resistant and shockproof plastics. The product, with long life, Is mainly used in AC 50/60Hz single-pole 230V or two, three, four-pole 400V circuit for overload and shortcircuit protection as well as for unfrequented on-and-off switching electric equipment and lighting circuit in normal case. The product complies with EN/IEC60898.

ANTM1

ANQ3-G Self-resettable Overvoltage and Undervoltage Protection Device is developed under the electricity situation. Control circuit components was imported , This products are of modulization standards, excellent performance and reliability. Can work under abnormal voltage conditions. When the utility voltage exceeds the protector operating voltage, the protector can quickly and reliably cut off the power to protect the electrical safety. When the mains voltage back to normal, the protector can automatically turn on the power to restore power supply, all the functions of all automatic implementation, without staff operation. LED light switch on the panel can indicate the working conditions of protection. Green means normal, red means abnormal. When in red, the light protection function starts to cut off the power supply. This series of products is compact, beautiful appearance, installation rail is same with DZ47 (45) .

ANQ3-G

Short-circuit protection which SPD products needed was integrated in the SPD module, no fuse neeed, It adopts 35mm standard rail， Compared with the conventional fuse + SPD module, it has the following advantages: Residual voltage decreased by 50% or more.In the case of separate installation of fuses, in the fuse itself and the connection wires are inductor, so there must be a great residual pressure. The use of ANT1-R products, this part of the residual pressure is almost zero, it can be more effective protection equipment.

ANT1-R

ANT1-(C)8 series solar surge protective device is suitable for the new energy solar power generation system, it’s working voltage covers 500V,800V and 1000V .It is installed in the main power system at DC circuit ,to protect against the indirect lightning current ,direct lighting current or other instantaneous over voltage.

ANT1-C8

ANT5 series surge protective (in short :SPD,alias:surge protector,surge arrecter) is suitable for TN-S,TN-C-S,TT,IT,ect. Power supply system of AC 50/60 HZ, =380V,installed on joint of LAPZOA zone or LAPZOB and LAPZ1 zone ,which protects the electric network not shocked by the thunder and lightning, it’s designed according to IEC61643-1,GB18802.1, it adopts 35mm standard rail, here is a failure release mounted on the module of suge protective device, When the SPD fails in breakdown for over-heat and over-current,the failure release will help electric device separate from the power system and give the indication signal, green means normal ,red means abnormal.

ANT1-5

ANT4 series surge protective device (in short.SPD.alias. surge protector,surge arrecter) is suitable for TT,TN-C,TN-S,IT ect.Power supply system of AC 50/60HZ. ≤380V,Which protects the elective device not shocked by the thunder or surge over-voltage.

ANT4

ANT1-1~3 series surge protective (in short :SPD,alias:surge protector,surge arrecter) is suitable for TN-S,TN-C-S,TT,IT,ect. Power supply system of AC 50/60 HZ, =380V,installed on joint of LAPZOA zone or LAPZOB and LAPZ1 zone ,which protects the electric network not shocked by the thunder and lightning, it’s designed according to IEC61643-1,GB18802.1, it adopts 35mm standard rail, here is a failure release mounted on the module of suge protective device, When the SPD fails in breakdown for over-heat and over-current,the failure release will help electric device separate from the power system and give the indication signal, green means abnormal ,It’s also could be replaced for the module when has operating voltage.

ANT1-1~3

ANT1-B series surge protective (in short :SPD,alias:surge protector,surge arrecter) is suitable for TN-S,TN-C-S,TT,IT,ect. Power supply system of AC 50/60 HZ, =380V,installed on joint of LAPZOA zone or LAPZOB and LAPZ1 zone ,which protects the electric network not shocked by the thunder and lightning, it’s designed according to IEC61643-1,GB18802.1, it adopts 35mm standard rail, here is a failure release mounted on the module of suge protective device, When the SPD fails in breakdown for over-heat and over-current,the failure release will help electric device separate from the power system and give the indication signal, green means abnormal ,It’s also could be replaced for the module when has operating voltage.

ANT1-B

ANT1-C series surge protective (in short :SPD,alias:surge protector,surge arrecter) is suitable for TN-S,TN-C-S,TT,IT,ect. Power supply system of AC 50/60 HZ, =380V,installed on joint of LAPZO or LAPO1 , LPZ2 zone ,which protects the electric network not shocked by the thunder and lightning, it’s designed according to IEC61643-1,GB18802.1, it adopts 35mm standard rail, here is a failure release mounted on the module of suge protective device, When the SPD fails in breakdown for over-heat and over-current,the failure release will help electric device separate from the power system and give the indication signal, green means abnormal ,It’s also could be replaced for the module when has operating voltage.

ANT1-C ARC

ANT1-C series surge protective (in short :SPD,alias:surge protector,surge arrecter) is suitable for TN-S,TN-C-S,TT,IT,ect. Power supply system of AC 50/60 HZ, ≤380V,installed on joint of LAP1 or LPZ2 and LPZ3.it’s designed according to IEC61643-1,GB18802.1, it adopts 35mm standard rail, here is a failure release mounted on the module of suge protective device, When the SPD fails in breakdown for over-heat and over-current,the failure release will help electric device separate from the power system and give the indication signal, green means abnormal ,It’s also could be replaced for the module when has operating voltage.

ANT1-C

ANT1-D series surge protective device(in short; SPD, alias; surge protector,surge arrecter)is suitable for TN-S,TN-C-S,TT,I Tect.Power supply system of AC 50/60 HZ,=380V,installed on joint of LAP1 or LPZ2 and LPZ3,it’s design according to IEC61643-1,GB18802.1 , it’s adopts 35mm standard rail,there is a failure release mounted on the module of suge protective device. When the SPD fails in breakerdown for over-heat and over-current,the failure erelease will help electric device separate from the power system and give the indication signal, green means abnormal, it’s also could be replaced for the module when has operating voltage.

ANT1-D

ANT1-A50 series of graphite gap type surge protective device(a Lightning arrester, 10/35 μs waveform) 3 according to IEC and GB standards. Equipment system used in high risk area of the power supply of the first primary surge protection. Can prevent lightning strike, all kinds of surge current, pass A combination of different number of suitable to single-phase. Three-phase power supply line. dieModular design, standard 35mm rail mounted, installed in the building The total power distribution cabinet(box),outdoor distribution cabinet(box),with lightning current high. The discharge capacity,free wheeling,single module maximum impulse current (10/35 μS)Sbranc Don’t reach limp=15KA,limp=25KA,limp=35KA ,limp=50KA maxim umdischarge current (8/20 μS) Can reach Imax=100KA,Imax=150KA,Imax=160KA,Imax=200KA.

ANTI-A50

Molded case circuit breakers can cut off the current automatically when the current exceeds the trip setting. Plastic shell refers to the use of plastic insulators as a device shell, used to isolate the metal between the conductor and ground. Molded case circuit breakers typically contain thermal-magnetic trip-out units, while larger molded-case circuit breakers are equipped with solid-state trip sensors. The trip unit is divided into: thermal magnetic tripping and electronic release. Commonly used, rated current total of the following 16 25 30 40 50 60 75 80 100 125 160 200 225 250 315 350 400 500 630 A

ANM13(VL)

MCCB(molded case circuit breaker) is a device to protect the equipment from short-circuit, overload. Our MCCB are made according IEC60947-2 standards, rated current from 63A to 1600A are available. Based on the tripping method, we cover thermal-magnetic type and electronic type. According to your application, auxiliary contact, shunt trip, alarming contact, under voltage modular, rotary handle, insert base and residual protection modular etc. are ready well for your special requirement. Mini circuit breaker is the new product adopt the newest modern highly technologic.Its excellent performance is depending on the quick trip and strong .It has some new design for choose.

ANM10(NF-CW)

« First « 1 2 3 4 » Last »

Circuit Breaker & AutomaticTransfer Switch

Contactor & Industrial electrical appliances

2015 © Copyright WENZHOU CHENLU IMP.&EXP. CO.,LTD TEL: +86 13757778680 FAX: Design By:Otree.cn

Sitemap Google+ Product Summary DC circuit breaker PRIVACY POLICY